Hiya,
I need a little help to OC my Q6600 to 3.4 GHz. Below are my specs:
Q6600
Gigabyte EP45 DS3R
OCZ Reaper HPC PC6400 800mhz 2X2GB
Xigmatek S1328 CPU Cooler
Radeon 4780 with Accelero twinturbo
Core Temps 0.99.3 @3.2:
IDLE LOAD (Small FFT 30 minutes)
Core #0: 37C 59-60C
Core #1: 35C 59-60C
Core #3: 30C 55C
Core #4: 34C 55C
CPUZ voltage: 1.392v 1.328v
CPUZ DRAM: 426 MHZ
CPUZ FSB:DRAM 5:6
timings: 4-4-4-12 2T
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.195
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 355 Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 150ps
MCH Clock Skew (ps)...................: <<< 250ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.)......: Disabled
(G)MCH Frequency Latch................: auto
Multiplier ....................................: 2.40b
Memory Frequency (Mhz) ..............: 854
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Advanced Timing Control
tRRD...........................................:4
tWTR..........................................:9
tWR............................................:5
tRFC...........................................:57
tRTP...........................................:5
Command Rate (CMD) ....................:2
Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p itxtvisited="1"></o:p>
<!-- / message --><!-- sig --></SPAN itxtvisited="1"><!-- / message -->
I need a little help to OC my Q6600 to 3.4 GHz. Below are my specs:
Q6600
Gigabyte EP45 DS3R
OCZ Reaper HPC PC6400 800mhz 2X2GB
Xigmatek S1328 CPU Cooler
Radeon 4780 with Accelero twinturbo
Core Temps 0.99.3 @3.2:
IDLE LOAD (Small FFT 30 minutes)
Core #0: 37C 59-60C
Core #1: 35C 59-60C
Core #3: 30C 55C
Core #4: 34C 55C
CPUZ voltage: 1.392v 1.328v
CPUZ DRAM: 426 MHZ
CPUZ FSB:DRAM 5:6
timings: 4-4-4-12 2T
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: 9
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 3.195
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 355 Mhz
PCI Express Frequency (Mhz) .........:Set to 100
C.I.A.2 .................................:[Disabled]
Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 150ps
MCH Clock Skew (ps)...................: <<< 250ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.)......: Disabled
(G)MCH Frequency Latch................: auto
Multiplier ....................................: 2.40b
Memory Frequency (Mhz) ..............: 854
DRAM Timing Selectable ................: [Manual]
Standard Timing Control
CAS Latency Time........................ 4
tRCD ......................................... 4
tRP'........................................... 4
tRAS.......................................... 12
Advanced Timing Control
tRRD...........................................:4
tWTR..........................................:9
tWR............................................:5
tRFC...........................................:57
tRTP...........................................:5
Command Rate (CMD) ....................:2
Channel A
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Channel B
Static tRead Value.........................:8
tRD Phase0 Adjustment...................:Auto
tRD Phase1 Adjustment...................:Auto
tRD Phase2 Adjustment .................:Auto
tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto
Twr2wr(Different Rank)...................:Auto
Twr2rd(Different Rank)...................:Auto
Trd2wr(Same/Diff Rank)..................:Auto
Dimm1 Clock Skew Control...............:Auto ps
Dimm2 Clock Skew Control...............:Auto ps
Motherboard Voltage ControlCPUMCH/ICHAdvanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]<?xml:namespace prefix = o ns = "urn:schemas-microsoft-com:office:office" /><o:p itxtvisited="1"></o:p>
<!-- / message --><!-- sig --></SPAN itxtvisited="1"><!-- / message -->
Comment