If this is your first visit, be sure to
check out the FAQ by clicking the
link above. You may have to register
before you can post: click the register link above to proceed. To start viewing messages,
select the forum that you want to visit from the selection below.
stasio same problem for me with B550I Aorus Pro AX, bios-idle-load goes up by 0.088:
ex. BIOS setting 1.400
idle reading is 1.440
load reading is 1.488!!!!
the difference is wayyyyy too much.
Thx for pointing that out
B550 Aorus Pro v1
1,45V set and I get 1,475V. Not that critical but my old x370 gaming 5 used what i set.
Also GB sets Vsoc to 1.2V instead of 1.1V
Cannot get to 1900fclk with Crucial Ballistix RGB DDR4 3600mhz CAS16. Neither when OC'ing the memory to 3800mhz nor when just enabling XMP for an un-sync'd MLCK>FCLK setup.
Also I notice that a lot of the memory timing OC settings are in HEX, not decimal.
4940 on ccx1 seems unreasonable? Is this with the Testboost.exe instead of a real workload?
Also look at effective clock speed instead and CB single score difference
That was with cyberpunk running in the background. cpuz 689 10070 and cinebench r23 22706. PBO controlling clock speeds with curve offset from -28 to -40 and EDC 230.
Cannot get to 1900fclk with Crucial Ballistix RGB DDR4 3600mhz CAS16. Neither when OC'ing the memory to 3800mhz nor when just enabling XMP for an un-sync'd MLCK>FCLK setup.
Also I notice that a lot of the memory timing OC settings are in HEX, not decimal.
As posted earlier.....
Open ticket with GB Technical support,any case is particular, so they need full information about this.
Thx for pointing that out
B550 Aorus Pro v1
1,45V set and I get 1,475V. Not that critical but my old x370 gaming 5 used what i set.
Also GB sets Vsoc to 1.2V instead of 1.1V
I mean, in your case it's 0.025, a reasonable difference...in my case it's almost 0.1V, it's RAM frying territory. I opened a ticked now.
And yeah the default SOC in the F11p BIOS is absolutely nuts, I turned it down.
I have GB B550 Aorus Elite 1.0.+ R5600X+ 2x8 TG 4000 CL 18 B-Die memmory . Im on F10 bios , i tried updating to F11n but result was bricked bios. ( Tried 3 different ways to update , from Windows , from BIOS , and from Q-FLASH - without boot). Everytime BIOS is bricked and i have to restore F10 bios via Q-FLASH.
Now i see there is F11p bios avaliable , any chance it is better and i will be able to update ? Which method is the best ? I don't want bricked bios again because it's pain in the ass to restore all OC settings and flashing back new ....
Should I be concerned?
Noticed my 5950x has been randomly restarting on my X570 Aorus Master on F30.
The BIOS is all at stock settings except for XMP and disabling SATA hot swap and not OCing anything.
Looking at event viewer, I see some WHEA event 18 errors and looking at the kernel logs from the crashes, it's a WHEA_UNCORRECTABLE_ERROR and blaming ntoskrnl.exe.
I'm hoping the inevitable final F31 BIOS will fix it, otherwise I dont know what else to point to that could be causing it.
What RAM do you have, how many and where are they installed (what slots) ?
Im kinda in same situation - however i cant get i stable at F30 at all.
F31o where i "underclock" my RAM i can get it stable at 3000Mhz
I have :
Aorus Master too
5950x
Tried with:
4x 3600Mhz QVL RAM but boots after 10s
Putting 2 sticks in A2 and B2 and underclock it to 3000Mhz then its "semi" stable.
Quite anoying to make a nice new build and then all i want for christmas was a stable system :P
(Havent tried F31q yet...)
What RAM do you have, how many and where are they installed (what slots) ?
Im kinda in same situation - however i cant get i stable at F30 at all.
F31o where i "underclock" my RAM i can get it stable at 3000Mhz
I have :
Aorus Master too
5950x
Tried with:
4x 3600Mhz QVL RAM but boots after 10s
Putting 2 sticks in A2 and B2 and underclock it to 3000Mhz then its "semi" stable.
Quite anoying to make a nice new build and then all i want for christmas was a stable system :P
(Havent tried F31q yet...)
I was having a lot of stability issues with F30 on an Aorus Master 5900x combo with gSkill Flare-x (2x8 3200c14), or TridentZ (2x16 4000c19 clocked down to 3600c16). No matter if I manually set safe timings or using XMP, every couple of boots the memory would error out and boot loop. F31q is the first time I have been able to run even XMP without any crashes, and have using it for about 4 days without issue, so would give it a try. I have not pushed the memory clocks up, but first time I have been able to run 3200c14 without issue, just as a precaution did push up the dram voltage to 1.40v.
Just updated to F11p BIOS on my B550 Aorus elite. What a disaster :
1. If you enable SAM ( Re size bar) M.2 ports are disabled or lost ( no boot options ).
2. Crashes even with 3600 memmory/1800 fclk - ERROR : : Cache Hierarchy Error. - NEVER EVER i had error like this , this is after updating BIOS . I'm rolling back to F10 had zero issues, i just wanted SAM.
Gigabyte is out of their minds releasing unstable bios like that.
I was having a lot of stability issues with F30 on an Aorus Master 5900x combo with gSkill Flare-x (2x8 3200c14), or TridentZ (2x16 4000c19 clocked down to 3600c16). No matter if I manually set safe timings or using XMP, every couple of boots the memory would error out and boot loop. F31q is the first time I have been able to run even XMP without any crashes, and have using it for about 4 days without issue, so would give it a try. I have not pushed the memory clocks up, but first time I have been able to run 3200c14 without issue, just as a precaution did push up the dram voltage to 1.40v.
Do the bootloops only happen during a boot from power off? Also, do you get bootloops with xmp disabled?
hi Guys,
Im running BIOS Version F31 on Auros Elite with 5950X and RTX 3080.
My CPU is not boosting above 4.9Ghz (not an issue to be honest) but my IDLE temps are around 60+ on Corsair H150i
I checked voltage in Ryzen Master and its never dropping below 1.4 and most of the Cores are not going to sleep when not gaming etc
has this been fixed in F31q? or should I downgrade to F30 for now? anyone having same issue?
everything is default in BIOS except XMP Enabled.
hi Guys,
Im running BIOS Version F31 on Auros Elite with 5950X and RTX 3080.
My CPU is not boosting above 4.9Ghz (not an issue to be honest) but my IDLE temps are around 60+ on Corsair H150i
I checked voltage in Ryzen Master and its never dropping below 1.4 and most of the Cores are not going to sleep when not gaming etc
has this been fixed in F31q? or should I downgrade to F30 for now? anyone having same issue?
everything is default in BIOS except XMP Enabled.
if more info is needed please let me know
thank you
I just had same issue then I realized it is caused by Epic Game Launcher. Just disable it on ur background.
Just updated to F11p BIOS on my B550 Aorus elite. What a disaster :
1. If you enable SAM ( Re size bar) M.2 ports are disabled or lost ( no boot options ).
2. Crashes even with 3600 memmory/1800 fclk - ERROR : : Cache Hierarchy Error. - NEVER EVER i had error like this , this is after updating BIOS . I'm rolling back to F10 had zero issues, i just wanted SAM.
Gigabyte is out of their minds releasing unstable bios like that.
That's what beta's are, bioses with a letter behind the numbers are beta, it's just a flash it at your own risk warning
Comment