F33a on Aorus Ultra rev 1.0... I'm finding that rebooting and going into BIOS causes some settings to be lost (but not all, and not a CMOS reset). One setting that is getting lost often is SVM. I enable it, but anytime I go back into BIOS to change something else, SVM is turned off.
Announcement
Collapse
No announcement yet.
GIGABYTE Latest Beta BIOS
Collapse
This is a sticky topic.
X
X
-
After 2 weeks with B550i AX, 5800x, BIOS F12
Ive now had the Bluetooth device disappear requiring an unplug. Intel drivers 22.20 may help but dont solve this long reported problem.
Ive not seen the Realtek 2.5Gb issues so far, using default Windows 10 drivers 10.39.212.2020
The Xbox Wireless Receiver USB is only happy in the red Gen 2 port, on other ports it lags or disconnects.
On every restart the ITE Device shows Set Address error.
BIOS settings, CSM disabled, ECO mode, XMP
In Windows 'Allow Turn Off' unticked in Power Management for hubs and devices in Device Manager and USB Selective Suspend disabled in Power Plan
Some of these issues may be the fault of the chip or module used, or the AMD B550 chipset or AGESA but they do seem more common with Gigabyte - I wish I had paid more attention to threads and customer reviews instead of website reviews when choosing the B550i over the Asus m/b
- Likes 1
Comment
-
Originally posted by rehsd View PostF33a on Aorus Ultra rev 1.0... I'm finding that rebooting and going into BIOS causes some settings to be lost (but not all, and not a CMOS reset). One setting that is getting lost often is SVM. I enable it, but anytime I go back into BIOS to change something else, SVM is turned off.
Comment
-
Originally posted by jwsg View PostThe Xbox Wireless Receiver USB is only happy in the red Gen 2 port, on other ports it lags or disconnects.
I now use the front ports of the chassis. I still occasionally experience disconnects, but the issue appears to be less frequent, and doesn't last quite as long (I lose the controller for a second, alt-tab twice, and it comes back, as opposed to 10-15 seconds on the rear ports).
I wonder if there's some kind of USB voltage drop, and the power draw required to maintain the signal is lower for the front ports...
Comment
-
Originally posted by jwsg View PostAfter 2 weeks with B550i AX, 5800x, BIOS F12
Ive now had the Bluetooth device disappear requiring an unplug. Intel drivers 22.20 may help but dont solve this long reported problem.
Ive not seen the Realtek 2.5Gb issues so far, using default Windows 10 drivers 10.39.212.2020
The Xbox Wireless Receiver USB is only happy in the red Gen 2 port, on other ports it lags or disconnects.
On every restart the ITE Device shows Set Address error.
BIOS settings, CSM disabled, ECO mode, XMP
In Windows 'Allow Turn Off' unticked in Power Management for hubs and devices in Device Manager and USB Selective Suspend disabled in Power Plan
Some of these issues may be the fault of the chip or module used, or the AMD B550 chipset or AGESA but they do seem more common with Gigabyte - I wish I had paid more attention to threads and customer reviews instead of website reviews when choosing the B550i over the Asus m/b
Comment
-
Originally posted by zalbard View PostInteresting, that's the very first port I tried, and that's where I discovered the issue.
I now use the front ports of the chassis. I still occasionally experience disconnects, but the issue appears to be less frequent, and doesn't last quite as long (I lose the controller for a second, alt-tab twice, and it comes back, as opposed to 10-15 seconds on the rear ports).
I wonder if there's some kind of USB voltage drop, and the power draw required to maintain the signal is lower for the front ports...
I did some investigating on the B550i and found
- the two case front header USB 3.0 (3.1 Gen1) are B550 chipset connected
- the red and type C Gen 2 ports are B550 chipset connected
- the remaining four 3.1 Gen1 rear ports are CPU connected
Problems happen for me if all of one "group" above is used at the same time - i.e. both front panel USBs, or the red and the type C, or all 4 rear ports together. An example is the mouse lagging or disappearing when both front ports are used together. So I connect the wireless mouse to the front USB, the xbox receiver to the red port, and a keyboard dongle for when the bluetooth drops to of the rear gen 1 ports.
I expected problems due to SATA ports plus M2 plus Ethernet chip plus Gen 1 and Gen 2 ports all coming from the B550 which only has limited PCIe lanes to the CPU but for me problems start when I use both front ports together or both gen 2 ports etc - so it could be power design or hub bandwidth issues.
- Likes 1
Comment
-
Originally posted by jwsg View PostOn every restart the ITE Device shows Set Address error.
but for bluetooth it only happened to me once it disappeared in over two months, i use xbox controller connected through bluetooth and it never disconnect
Comment
-
Originally posted by jwagriff View Post
To add a bit more weight to this: tried disabling fast startup within windows, and so far I haven't had this issue come back. It's also off in the BIOS. Maybe both options have to be switched to on to avoid conflicts?
Worked for me (so far at least) so might be worth trying for you?
Comment
-
Tried many things from this thread to solve problems with Realtek 2.5Gb... lan settings, lan drivers, chipset drivers, bios, but nothing to work, Realtek is still loses connection. But once i tried to remove AMD Chipset drivers and after that all been fine :) But i didn't stop there... i tried to install it without some modules, and finally i found which driver makes issues for me - AMD SMbus Driver, without it i have stable work of Realtek and Bluetooth... reported this to support this find two days ago. Maybe also help for somebody, while we wait for fix ;)
AMD R7 5800x (dual CCD as shows CTR2.0) | B550 AORUS ELITE AX V2 F13a | Adata XPG SPECTRIX D50 2x16 | Palit RTX 3070 GamingPro | Chieftec A-90 750W PSU
- Likes 2
Comment
-
Hi!
I have the following setup:
Gigabyte Aorus X570 Xtreme Rev. 1.1 Mainboard
5950X CPU
2 Kits of G.Skill F4-3800C14D-32GTZN (4x16GB)
I can't run a fabric at anything i set.
No matter what I set, it stays at 1066Mhz (like auto setting)
Here a screenshot from cpu-z:
I did the settings under "DDR and Infinity Fabric Frequency/Timings" in the Bios f33a.
Maybe i forgot something to set in the bios?
Best regards!
Comment
Comment