Announcement
Collapse
No announcement yet.
GIGABYTE Latest Beta BIOS
Collapse
This is a sticky topic.
X
X
-
Re: GIGABYTE Latest Beta BIOS
Originally posted by stasio View PostNew BIOS updated:
GA-Z77X-UP5 TH - F5b
GA-Z77X-UP4 TH - F3c
G1.Sniper 3 - F6i
G1.Sniper q did for my UD5HM3 - F8a
GA-Z77X-UD5H - F9q
GA-Z77X-UD3H - F12l
GA-Z77X-D3H - F11c
GA-Z77-D3H - F17a
GA-Z77-DS3 - F8a
GA-Z77M-D3H - F10a
GA-Z77MX-D3H - F13e
- 01.Aug 12
See what F9q did for my UD5H over at ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***Gigabyte GA-Z77X-UD5H WB Motherboard
Intel Ivy Bridge i7 3770K clocked @ 4.5GHz
16GB Kingston Hyper-X Genesis 2133 RAM
Water cooling by XSPC RASA RS240 Kit
Sapphire HD 6850 1GB DDR5 GPU
1TB - RAID1 setup with Western Digital 6GB/Sec Drives
Corsair HX750W Professional PSU
Windows 7 Professional (x64) Build 7601
Comment
-
Re: GIGABYTE Latest Beta BIOS
It appears like F12L for the UD3H restored all the fixes and features which they removed in F12J, with the exception of Secure Boot. Didn't notice anything new compared to F12h, except that some of the existing settings were rearranged a bit. As a result of them re-adding the CSM settings, the HBA I have in the PCI-E x4 slot once again shows up, so I'm content with using this bios for the time being. 16GB of Samsung DDR3L @2133Mhz is still a no-go.Last edited by thebeing; 08-04-2012, 01:00 AM.
Comment
-
Re: GIGABYTE Latest Beta BIOS
Originally posted by 2therock View PostSatsio, I owe you a Beer!
See what F9q did for my UD5H over at ***Official***Z77X-D3H UD3H UD5H Discussion\Owners Club***
Originally posted by basschilperoord View PostWhat is changed in F10A for GA-Z77M-D3H?
I don't get why there aren't any changelogs for these BETA bios versions.Originally posted by Shura30 View Postwhat's new for the z77x-ud3h??Originally posted by amorak View PostAny comments on what the F17a BIOS for the Z77-D3H provides?Last edited by stasio; 08-04-2012, 12:56 AM.
Comment
-
Re: GIGABYTE Latest Beta BIOS
Originally posted by basschilperoord View PostThank you stasio.
Problem still occurs with my WUSB300N, I get slow boots when I plug it in.
As your problem is very specific,ask GGTS for help or advice.
Hope,you try each USB ports and had latest drivers installed.Last edited by stasio; 08-04-2012, 01:31 AM.
Comment
-
Re: GIGABYTE Latest Beta BIOS
Is there any chance of letting the powers that be know that on occasion both my USB 2 and 3 front ports (only) will not respond after being in S3 sleep mode. This is on my Z77x UD5H board. I have just flashed it to the latest BIOS so I will need to test that for longer to confirm. Everything else seems to work a treat but the front USB port can, at times, be iffy when resumed from sleep whilst other times they awake without issue.
As I use the sleep function all the time (Windows 7 x64 Home) I will only notice the port situation when I plug a stick or drive into it and thus it will then need a reboot to sort it out, which it always does.
Thanks :)Gigabyte DS3H Z77 board (being repaired) GA-Z77X-UD5H. 3570k CPU. 2x4GB Corsair LP DDR3 memory. Asus GTX 670 2GB GPU.
Comment
-
Re: GIGABYTE Latest Beta BIOS
When I had the Z77 D3H only the front left USB 3 port would work with my Toshiba 1TB USB 3 hard drive. The right one would only show it as needing to format (after doing so it would say it needed it again) or it would not show it at all. Both ports would work fine with my card reader and any stick. They would also work fine with my USB 2 hard drives.
On my UD5H board both front USB 3 ports will work fine with that HD.
Both boards will have issues with the front ports on occasion not waking up from sleep.
Latest drivers used for each board.
I have noted in other forums of similar issues with the front ports.Gigabyte DS3H Z77 board (being repaired) GA-Z77X-UD5H. 3570k CPU. 2x4GB Corsair LP DDR3 memory. Asus GTX 670 2GB GPU.
Comment
-
Re: GIGABYTE Latest Beta BIOS
Bios f9q DRAM voltage issue. (prev beta F9 had similar issue)
Correctly sets 1.35v for samsung green. But can not increase voltage. My Backup bios is F8 when i set 1.4v then switch off flip switch to Main bios (F9q) it then sets 1.4v. It seems F9q is using the voltage settings from Backup bios.Corsair Carbide 400R
Corsair AX-750W
Gigabyte Z77X-UP5 TH F12j
i7 [email protected]
Antec 620 Kuhler
16GB Gskill 2133 10 11 10 28 1N
Gigabyte 680 GTX OC3W
OCZ Vertex 4 256GB
Samsung 840 Pro 256GB
Seagate Barracuda 3TB ST3000DM001
Samsung HD204UI Spinpoint F4 2TB
Comment
-
Re: GIGABYTE Latest Beta BIOS
gigabyte z68x-ud3h-b3 with the latest uefi bios from this site. Usb3 ports are not working. The usb 3 controller get detected by windows and the latest eton usb3 drivers are installed (112) but when I try the port with my headset or a memory stick the ports detects nothing. I hope this will be fixed in next bios.
Comment
-
Re: GIGABYTE Latest Beta BIOS
Originally posted by irfs View PostBios f9q DRAM voltage issue. (prev beta F9 had similar issue)
Correctly sets 1.35v for samsung green. But can not increase voltage. My Backup bios is F8 when i set 1.4v then switch off flip switch to Main bios (F9q) it then sets 1.4v. It seems F9q is using the voltage settings from Backup bios.
Edit:
reset CMOS also.Last edited by stasio; 08-05-2012, 02:11 AM.
Comment
Comment