Announcement

Collapse
No announcement yet.

Help P45-UD3P & Q9300 OC to 3.2ghz!

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Help P45-UD3P & Q9300 OC to 3.2ghz!

    Would like to go to 3.2ghz Stable! Help with BIOS settings. Thanks!

    MB Intelligent Tweaker(M.I.T.)
    Robust Graphics Booster ...............: Auto
    CPU Clock Ratio ..........................: 7
    Fine CPU Clock Ratio.....................:.5
    CPU Frequency ...........................: 2.5ghz


    Clock Chip Control
    Standard Clock Control
    CPU Host Clock Control..................: [Disabled]
    CPU Host Frequency (Mhz) ............: 333 Mhz
    PCI Express Frequency (Mhz) .........: Auto

    C.I.A.2 .................................:[Disabled]


    Advanced Clock Control [Press Enter]
    CPU Clock Drive...........................: 800mV <<<
    PCI Express Clock Drive.................: 900mV <<<
    CPU Clock Skew (ps)....................: 0ps<<<
    MCH Clock Skew (ps)...................: 0ps<<<


    DRAM Performance Control
    Performance Enhance...................: [Turbo]
    Extreme Memory Profile (X.M.P.).....: Auto
    (G)MCH Frequency Latch...............: [Auto]
    System Memory Multiplier ..............: Auto
    Memory Frequency (Mhz) ..............: 1066
    DRAM Timing Selectable ................: [Auto]

    Standard Timing Control
    CAS Latency Time........................ 5
    tRCD ......................................... 5
    tRP'........................................... 5
    tRAS.......................................... 15

    Set all Suggested below to highest Values first. Then later you can lower, one at a time, testing as you go

    Advanced Timing Control
    tRRD........................................... 4
    tWTR.......................................... 4
    tWR............................................ 6
    tRFC........................................... 72
    tRTP........................................... 4
    Command Rate (CMD) ....................: 0

    Driving Strength Profiles
    Driving Strength ............................

    Channel A
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 6
    Twr2wr(Different Rank)...................:Auto 6
    Twr2rd(Different Rank)...................:Auto 5
    Trd2wr(Same/Diff Rank)..................:Auto 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Channel B
    Static tRead Value.........................: 11
    tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
    tRD Phase1 Adjustment...................:Auto
    tRD Phase2 Adjustment .................:Auto
    tRD Phase3 Adjustment..................:Auto
    Trd2rd(Different Rank)....................:Auto 6
    Twr2wr(Different Rank)...................:Auto 6
    Twr2rd(Different Rank)...................:Auto 5
    Trd2wr(Same/Diff Rank)..................:Auto 8
    Dimm1 Clock Skew Control...............:Auto ps
    Dimm2 Clock Skew Control...............:Auto ps

    Motherboard Voltage Control
    Voltage Type.... Auto
    CPUMCH/ICHDRAMAdvanced Settings
    Limit CPUID Max. to 3.....................: [Disabled]
    No-Execute Memory Protect............: [Enabled]
    CPU Enhanced Halt (C1E)................: [Enabled]
    C2/C2E State Support....................: [Disabled]
    x C4/C4E State Support..................: [Disabled]
    CPU Thermal Monitor 2(TM2) ...........: [Enabled]
    CPU EIST Function.........................: [Enabled]
    Virtualization Technology................: [Enabled] Enabled if you use Vmware/Virtual PC

  • #2
    Re: Help P45-UD3P &amp; Q9300 OC to 3.2ghz!

    I have a Freezer 7 Pro, Temps at BIOS ideal at 24c.
    in Windows im at 36c/39c jumps because my cpu is clocking from 2ghz to 2.5ghz.


    I would like to reach 3.2ghz Stable.

    Please let me know what to change. Thank you


    MOBO = P45-UD3P BIOS= F4
    CPU = Q9300 @ 2.5ghz
    Memory = OCZ Platinum PC8500 / 5-5-5-15 @2.1v 1066
    Cooler= Freezer 7 Pro
    PSU= 500 NEO Antec

    Comment

    Working...
    X