gigabyte doubleboot problem

[vvikas]

hello,
i am facing a strange problem here . my specs are
e8400
gigabyte ep45 DS3L
gskill 2x2 gb 800mhz
my problem is when i try to overclock porcessor by increasing its fsb from 333 to higher it overclock well but when i start my sys from coldboot( switching on power from wall soket and psu) it double boots but but runs with overclocked setting stable. problem goes when restart while power still on or reduce fsb below 333mhz.
i want to know is this problem same with other gigabyte mobo or updating bios will solve this.

[Lsdmeasap]

Re: gigabyte doubleboot problem

Well what BIOS are you using? That happens if you are using the incorrect settings, and it can be at bootup or on a reboot. And can be double or triple boot.

Please link me to your ram or give me the model #, and post me the settings you are using that fail and I will advise back

This is Just a template I use to ask people their settings, pay no attention to the numbers in it, replace with yours

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 
Fine CPU Clock Ratio.....................:.0
CPU Frequency ...........................: 


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: 
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................
tRCD .........................................
tRP'...........................................
tRAS..........................................

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................
tWTR..........................................
tWR............................................
tRFC...........................................
tRTP...........................................
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................

[b]Channel A[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6/7-10 333/B MCH - 8/9-12 400/D MCH
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]
Voltage Type.………... Manual
[b]CPU[/b]
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 
MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.550V............: <<< Leave
ICH Core…………...……1.100V............: <<< Leave

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB