Re: UD3P+8500 Over 4.1ghz is it posbile?
tWR needs to be higher then tWTR and I see it is not, but that may be all due to your multi you are using or the use of auto. Set them manually for sure so you can sort that out as a non issue
If you are still using the settings from post one, try these with all my changes noted
Hey not sure what FSB you are trying to use? You have 490 and 500 listed?
******Gigabyte EP45 UD3P******
E8500 490 X 8.5 4165MHz
Crucial Ballistix PC2-8500 BL2KIT12864AA106A 2x1gb
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ 0.5 ]
CPU Frequency 4.0GHz...........................[ 490 x 8.5 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 490 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 ..................................................[Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ Auto ]
System Memory Multipler.........................[ 2.00D ] You can likely also use 2.00B I could use the B strap without issues with the Crucial I reviewed up to 1100+ But yes, D would be easier on things for now maybe, but then again....
Memory Frequency 1066...........................[ 980 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ 4 ]
tWTR............................................[ 4 ]
tWR.............................................[ 8 ]
tRFC............................................[ 54 ]
tRTP............................................[ 4 ]
Command Rate (cmd)..............................[ 2T ]
******Channel A Timing Settings******
Static tRead Value [ 11 ] ................[ 9 ] << Set 10 for now
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ] << Set 1066
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 11 ] ................[ 9 ] << Set 10 for now
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ] << Set 1066
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.25 ]...................[ 1.39375 ]
CPU Termination [ 1.20 ]...................[ 1.30 ] << Try 1.28, and 1.34
CPU PLL [ 1.50 ]...................[ 1.59 ]
CPU Reference [ 0.760 ]...................[ 0.878 ] ET6 Show 0.815 << AUTO
MCH Core [1.1 ]...................[ 1.46 ] << MUCH Less, try 1.1-1.32
MCH Reference [0.760 ]...................[ 0.743 ] ET6 Show 0.68 (Might want to try Auto until you are sure this is a issue. You should be able to boot thru with Auto, this would only be for fine tuning stability later
MCH/DRAM Refernce [0.900 ]...................[ Auto ]
ICH I/O [1.500 ]...................[ 1.570 ]
ICH Core [1.100 ]...................[ 1.200 ]
DRAM Voltage [1.800 ]...................[ 2.08-2.12 ] More is not better, for sure since you are not even running it at stock speed or super tight timings
DRAM Termination [0.900 ]...................[ Auto ]
Channel A Ref [0.900 ]...................[ Auto ]
Channel B Ref [0.900 ]...................[ Auto ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ] << Enabled, this would be disabling a core or more, have you looked into that?
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ] << Enabled
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ] << Enabled
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Enabled ] << if you are not using Vmware/Virtual PC then disable this
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB[/code]
tWR needs to be higher then tWTR and I see it is not, but that may be all due to your multi you are using or the use of auto. Set them manually for sure so you can sort that out as a non issue
If you are still using the settings from post one, try these with all my changes noted
Hey not sure what FSB you are trying to use? You have 490 and 500 listed?
******Gigabyte EP45 UD3P******
E8500 490 X 8.5 4165MHz
Crucial Ballistix PC2-8500 BL2KIT12864AA106A 2x1gb
Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ 0.5 ]
CPU Frequency 4.0GHz...........................[ 490 x 8.5 ]
******Clock Chip Control******
CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 490 ]
PCI Express Frequency (Mhz).....................[ 100 ]
C.I.A 2 ..................................................[Disabled]
******Advanced Clock Control******
CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]
******DRAM Performance Control******
Performance Enhance [Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ Auto ]
System Memory Multipler.........................[ 2.00D ] You can likely also use 2.00B I could use the B strap without issues with the Crucial I reviewed up to 1100+ But yes, D would be easier on things for now maybe, but then again....
Memory Frequency 1066...........................[ 980 ]
DRAM Timing Selectable..........................[ Manual ]
CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]
******Advanced Timing Control******
tRRD............................................[ 4 ]
tWTR............................................[ 4 ]
tWR.............................................[ 8 ]
tRFC............................................[ 54 ]
tRTP............................................[ 4 ]
Command Rate (cmd)..............................[ 2T ]
******Channel A Timing Settings******
Static tRead Value [ 11 ] ................[ 9 ] << Set 10 for now
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel A Driving Settings******
Drive Strength Profile..........................[ Auto ] << Set 1066
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Channel B Timing Settings******
Static tRead Value [ 11 ] ................[ 9 ] << Set 10 for now
tRD Phase0 Adjustment [ 0 ] ................[ Auto ]
tRD Phase1 Adjustment [ 0 ] ................[ Auto ]
tRD Phase2 Adjustment [ 0 ] ................[ Auto ]
tRD Phase3 Adjustment [ 0 ] ................[ Auto ]
tRD 2rd (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2wr (Differnt Rank) [ 6 ] ................[ Auto ]
tWR 2rd (Differnt Rank) [ 5 ] ................[ Auto ]
tRD 2wr (Same/Difft Rank) [ 8 ] ................[ Auto ]
Dimm 1 Clock Skew Control.......................[ Auto ]
Dimm 2 Clock Skew Control.......................[ Auto ]
DDR Write Training..............................[ Auto ]
******Channel B Driving Settings******
Drive Strength Profile..........................[ Auto ] << Set 1066
Data Driving Pull Up Level......................[ Auto ]
cmd Driving Pull Up Level.......................[ Auto ]
ctrl Driving Pull Up Level......................[ Auto ]
clk Driving Pull Up Level.......................[ Auto ]
Data Driving Pull Down Level....................[ Auto ]
cmd Driving Pull Down Level.....................[ Auto ]
ctrl Driving Pull Down Level....................[ Auto ]
clk Driving Pull Down Level.....................[ Auto ]
******Motherboard Voltage Control******
Load-Line Calibration [Enabled]
CPU Vcore [ 1.25 ]...................[ 1.39375 ]
CPU Termination [ 1.20 ]...................[ 1.30 ] << Try 1.28, and 1.34
CPU PLL [ 1.50 ]...................[ 1.59 ]
CPU Reference [ 0.760 ]...................[ 0.878 ] ET6 Show 0.815 << AUTO
MCH Core [1.1 ]...................[ 1.46 ] << MUCH Less, try 1.1-1.32
MCH Reference [0.760 ]...................[ 0.743 ] ET6 Show 0.68 (Might want to try Auto until you are sure this is a issue. You should be able to boot thru with Auto, this would only be for fine tuning stability later
MCH/DRAM Refernce [0.900 ]...................[ Auto ]
ICH I/O [1.500 ]...................[ 1.570 ]
ICH Core [1.100 ]...................[ 1.200 ]
DRAM Voltage [1.800 ]...................[ 2.08-2.12 ] More is not better, for sure since you are not even running it at stock speed or super tight timings
DRAM Termination [0.900 ]...................[ Auto ]
Channel A Ref [0.900 ]...................[ Auto ]
Channel B Ref [0.900 ]...................[ Auto ]
******Advanced BIOS Features******
CPU Multithreading..............................[ Disabled ] << Enabled, this would be disabling a core or more, have you looked into that?
Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Disabled ] << Enabled
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Disabled ] << Enabled
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Enabled ] << if you are not using Vmware/Virtual PC then disable this
Integrated Peripherals
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB[/code]
Comment