ep45-ud3p for starters

[BigDaddyReg]

I recently purchased a ep45-ud3p motherboard with a Intel Q6600, and a G'skill 4GB (2 x 2GB) F2-6400CL5D-4GBPQ. I also use an
XIGMATEK HDT-S1283 120mm Rifle CPU Cooler


Right now I am just looking for the non overclocked settings to get the system setup. This is my first post so please don't flame me

[Lsdmeasap]

Re: ep45-ud3p for starters

Thanks for posting here, and putting your spec's

Here would be optimal settings for a NON Overclock, but with EIST And C1E (Speedstep) Disabled for a overclock in mind. That just allows your CPU to run at full stock speeds always and so you will be ready to overclock later. If you do not want to overclock then you can, if you wish, leave C1E and EIST Enabled

[b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b]
Robust Graphics Booster ...............: Auto or Fast
CPU Clock Ratio ..........................: 9
CPU Frequency ...........................: 2.4Ghz


[b][u]Clock Chip Control [/u][/b]
[b][u]Standard Clock Control[/u][/b]
CPU Host Clock Control..................: [Enabled] 
CPU Host Frequency (Mhz) ............: 266Mhz
[B]PCI Express Frequency (Mhz) .........:Set to 100[/B]

C.I.A.2 .................................:[Disabled]


[b][u]Advanced Clock Control [Press Enter][/u][/b]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: <<< 
MCH Clock Skew (ps)...................: <<< 


[b][u]DRAM Performance Control[/u][/b][u][/u]
[B]Performance Enhance...................: [STANDARD][/B]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: 3.00A
Memory Frequency (Mhz) ..............: 800Mhz
DRAM Timing Selectable ................: [Manual]

[b]Standard Timing Control[/b]
CAS Latency Time........................5
tRCD .........................................5
tRP'...........................................5
tRAS..........................................15/18

Set all Suggested below to highest Values first.  Then later you can lower, one at a time, testing as you go

[b][u]Advanced Timing Control[/u][/b]
tRRD...........................................3-4
tWTR..........................................3-5
tWR............................................4-6
tRFC...........................................52-62
tRTP...........................................3-5
Command Rate (CMD) ....................:2

[u][b]Driving Strength Profiles[/b][/u][b][/b]
Driving Strength ............................800/1066 (Set last, and benchmark/test both to see which you like best)

[b]Channel A[/b]
Static tRead Value.........................:6-10
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b]Channel B[/b]
Static tRead Value.........................:6-10
 tRD Phase0 Adjustment...................:Auto <<< Leave for all below as well
tRD Phase1 Adjustment...................:Auto
 tRD Phase2 Adjustment .................:Auto
 tRD Phase3 Adjustment..................:Auto
Trd2rd(Different Rank)....................:Auto 
Twr2wr(Different Rank)...................:Auto 
Twr2rd(Different Rank)...................:Auto 
Trd2wr(Same/Diff Rank)..................:Auto 
Dimm1 Clock Skew Control...............:Auto  ps
Dimm2 Clock Skew Control...............:Auto  ps

[b][U]Motherboard Voltage Control[/U][/b][U][/U]

[b]CPU[/b]
CPU Vcore….……….........................:Auto if not overclocking, if you are overclocking please do find and set your own voltages

CPU Termination…..... 1.200V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.2-1.5 depending on Vcore, try to keep at least .1 under vcore.  Auto is fine if not overclocking

CPU PLL…………………....1.500V*.......: << If overclocking Please set to stock, Auto overvolts this way to much.  Optimal range for overclock would be 1.5-1.65.  Auto is fine if not overclocking

CPU Referen.…………....0.755V*.......: <<< .64% Of Vtt (Termination above) Auto Will set this correctly 

CPU Reference2………,,0.800V*.......:<<< .67% Of Vtt (Termination above) Auto Will set this correctly 

[b]MCH/ICH[/b]
MCH Core…………….....1.100V...........: << 1.20-1.3 (1.20-1.24 often plenty)  If you seem to have issues with this setting also try 1.05 as sometimes this helps but the norm would be 1.20-1.3 for 2x2GB

MCH Reference….…….0.800V...........; <<< Leave
MCH/DRAM Ref.…......0.900V...........: <<< Leave
ICH I/O……………….....1.500V............: <<< 1.5-1.55
ICH Core…………...……1.100V............: <<< 1.14-1.2

[b]DRAM[/b]
DRAM Voltage ……....1.800V............: 1.85-1.95 
DRAM Termination .…0.900V............: <<< Leave
Channel A Reference 0.900V............: <<< Leave
Channel B Reference 0.900V............: <<< Leave

[b][U]Advanced Settings[/U][/b][U][/U]
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Enabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Enabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled] Enabled if you use Vmware/Virtual PC

[b][U]Integrated Peripherals[/U][/b][U][/U]
Legacy USB Storage Detect ..............[Disabled] *Note* Must be enabled to flash from USB