Before I start, I want to say that this is my first time overclocking but have been building computers for years (this computer being #8) and would not have gotten thus far with out the information on this forum. I feel that I'm getting very close to 4.00ghz stabilized but fail the Prime95 "Small FFTs" on Core 4 after about 20 minutes, FATAL ERROR: Rounding was 0.5, expecting less then 0.4. I have been able to pass the Memtest86+ for 2 hours, OCCT for 1 hour and Prime95 Blend for 4 hours. My temperature's never go higher then 53 Celsius, so heating does not seem to be a problem. I have tried to clock my RAM to the rated 4-4-4-12 @ 1.90v without success, but want to get the processor stable before I try again. Looking forward to your assistance and getting this build a little more stable.
Code:
[B]--> MB Intelligent Tweaker (M.I.T.) <--[/B] Robust Graphics Booster ...............: Fast CPU Clock Ratio .......................: 9 Fine CPU Clock Ratio ..................: 0 CPU Frequency .........................: 4.00 GHz [B]--> Clock Chip Control <-- [/B] [B]>>> Standard Clock Control[/B] CPU Host Clock Control ................: [Enabled] CPU Host Frequency (Mhz) ..............: 445 PCI Express Frequency (Mhz) ...........: 100 C.I.A.2 ...............................: [Disabled] [B]>>> Advanced Clock Control[/B] CPU Clock Drive .......................: 800 PCI Express Clock Drive ...............: 900 CPU Clock Skew (ps) ...................: 0ps MCH Clock Skew (ps) ...................: 0ps [B]--> DRAM Performance Control <--[/B] Performance Enhance ...................: [STANDARD] (G)MCH Frequency Latch ................: [Auto] System Memory Multiplier .......(SPD)..: 2.00D Memory Frequency (Mhz) ..........800...: 890 DRAM Timing Selectable .........(SPD)..: [Manual] [B]>>> Standard Timing Control[/B] CAS Latency Time .................5....: 5 tRCD .............................5....: 5 tRP ..............................5....: 5 tRAS .............................18...: 15 [B]>>> Advanced Timing Control[/B] tRRD .............................3....: 3 tWTR .............................3....: 3 tWR ..............................6....: 6 tRFC .............................52...: 52 tRTP .............................3....: 3 Command Rate (CMD) ...............0....: 2 [B]--> Channel A <--[/B] [B]>>> Timings Settings[/B] Static tRead Value ...............11...: 10 tRD Phase0 Adjustment ............0....: [Auto] tRD Phase1 Adjustment ............0....: [Auto] tRD Phase2 Adjustment ............0....: [Auto] tRD Phase3 Adjustment ............0....: [Auto] Trd2rd(Different Rank) ...........6....: [Auto] Twr2wr(Different Rank) ...........6....: [Auto] Twr2rd(Different Rank) ...........5....: [Auto] Trd2wr(Same/Diff Rank) ...........8....: [Auto] Dimm1 Clock Skew Control ..............: [Auto] Dimm2 Clock Skew Control ..............: [Auto] [B]>>> Driving Settings[/B] Driving Strength Profile...............: 800MHz [B]--> Channel B <---[/B] [B]>>> Timing Settings[/B] Static tRead Value ...............11...: 10 tRD Phase0 Adjustment ............0....: [Auto] tRD Phase1 Adjustment ............0....: [Auto] tRD Phase2 Adjustment ............0....: [Auto] tRD Phase3 Adjustment ............0....: [Auto] Trd2rd(Different Rank) ...........6....: [Auto] Twr2wr(Different Rank) ...........6....: [Auto] Twr2rd(Different Rank) ...........5....: [Auto] Trd2wr(Same/Diff Rank) ...........8....: [Auto] Dimm1 Clock Skew Control ..............: [Auto] Dimm2 Clock Skew Control ..............: [Auto] [B]>>> Driving Settings[/B] Driving Strength Profile...............: 800MHz [B]--> Motherboard Voltage Control <--[/B] [B]>>> CPU[/B] Load-Line Calibration .................: [Disabled] CPU Vcore ...............1.27500V......: 1.36250V CPU Termination ........ 1.200V........: 1.240V CPU PLL .................1.500V........: 1.570V CPU Referen .............0.760V........: [Auto] [B]>>> MCH/ICH[/B] MCH Core ................1.100V........: 1.220V MCH Reference ...........0.760V........: [Auto] MCH/DRAM Ref ............0.900V........: [Auto] ICH I/O .................1.500V........: 1.570V ICH Core ................1.100V........: 1.200V [B]>>> DRAM[/B] DRAM Voltage ............1.800V........: 2.000V DRAM Termination ........0.900V........: [Auto] Channel A Reference .....0.900V........: [Auto] Channel B Reference .....0.900V........: [Auto] [B]--> Advanced Settings <--[/B] Limit CPUID Max. to 3 .................: [Disabled] No-Execute Memory Protect .............: [Enabled] CPU Enhanced Halt (C1E) ...............: [Disabled] C2/C2E State Support ..................: [Disabled] x C4/C4E State Support ................: [Disabled] CPU Thermal Monitor 2(TM2) ............: [Enabled] CPU EIST Function .....................: [Disabled] Virtualization Technology .............: [Disabled] [B]--> Integrated Peripherals <--[/B] Legacy USB Storage Detect .............: [Disabled]
Comment