Question for other EP45-UD3P owners who hit 500FSB and above

[Octopuss]

I just wanted to check what kind of voltages are you using for stable 500FSB configuration (anything above is welcome too).
Could you post your templates? Just the last part from bottom of M.I.T. section if possible. I am also interested in memory straps you use.
Thanks!

[Lsdmeasap]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

Did you do a search for UD3P yet? If not I would suggest that, do an advanced search, then choose by titles only and then enter UD3P and or *-UD3P and you should have plenty of posts with settings used.

500 FSB is often of course in the upper ranges of voltages, so you may need to turn your CPU fan up a bit Just kidding around cause I see you have "Slow" in your signature on it

[Octopuss]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

There's LOADS of UD3P threads around here! :) I saw several, but it is loads of text. It's not laziness, I just find it better this way rather than browsing throught maybe hundreds of posts :P

[BoombasticSloth]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

E8400 500 X 8.5 = 4250 MHz F9 BIOS

Robust Graphics Booster.........................[ Auto ]
CPU Clock Ratio.................................[ 8 ]
Fine CPU Clock Ratio............................[ 0.5 ]
CPU Frequency 4.25GHz............................[500 x 8.5]

******Clock Chip Control******

CPU Host Clock Control..........................[ Enabled ]
CPU Host Frequency (Mhz)........................[ 500 ]
PCI Express Frequency (Mhz).....................[ 100 ] 
C.I.A 2 ........................................[Disabled]

******Advanced Clock Control******

CPU Clock Drive.................................[ 800mv ]
PCI Express Clock Drive.........................[ 900mv ]
CPU Clock Skew..................................[ 0ps ]
MCH Clock Skew..................................[ 0ps ]

******DRAM Performance Control******

Performance Enhance ............................[Standard]
Extreme Memory Profile (XMP)....................[ Disabled ]
(G) MCH Frequency Latch.........................[ auto ] 
System Memory Multipler.........................[ 2.00D ]
Memory Frequency 1066...........................[ 1000]
DRAM Timing Selectable..........................[ Manual ]

CAS Latency Time................................[ 5 ]
tRCD............................................[ 5 ]
tRP.............................................[ 5 ]
tRAS............................................[ 15 ]

******Advanced Timing Control******

tRRD............................................[Auto]
tWTR............................................[Auto]
tWR.............................................[Auto]
tRFC............................................[Auto] 
tRTP............................................[Auto]
Command Rate (cmd)..............................[ 2 ] 


**************************************

Driving Strength Profiles
Driving Strength ...............................[ 1066 ]  

Channel A
Static tRead Value..............................[ 11 ]  
tRD Phase0 Adjustment...........................[Auto]
tRD Phase1 Adjustment...........................[Auto]
tRD Phase2 Adjustment ..........................[Auto]
tRD Phase3 Adjustment...........................[Auto]

Trd2rd(Different Rank)..........................[Auto]
Twr2wr(Different Rank)..........................[Auto]
Twr2rd(Different Rank)..........................[Auto]
Trd2wr(Same/Diff Rank)..........................[Auto]

Dimm1 Clock Skew Control........................[Auto]
Dimm2 Clock Skew Control........................[Auto]
DDR Write Training..............................[Auto]

Channel B
Static tRead Value..............................[ 11 ]  
tRD Phase0 Adjustment...........................[Auto]
tRD Phase1 Adjustment...........................[Auto]
tRD Phase2 Adjustment ..........................[Auto]
tRD Phase3 Adjustment...........................[Auto]

Trd2rd(Different Rank)..........................[Auto]
Twr2wr(Different Rank)..........................[Auto]
Twr2rd(Different Rank)..........................[Auto]
Trd2wr(Same/Diff Rank)..........................[Auto]

Dimm1 Clock Skew Control........................[Auto]
Dimm2 Clock Skew Control........................[Auto]
DDR Write Training..............................[Auto]

******Motherboard Voltage Control******

Load-Line Calibration ..........................[Disabled]
CPU Vcore [ 1.175 ].............................[ 1.2875 ]
CPU Termination [ 1.20 ]........................[ 1.240 ] 
CPU PLL [ 1.50 ]................................[ 1.50 ] 
CPU Reference [ 0.760 ].........................[ 0.770 ] 

MCH Core [1.1 ].................................[ 1.220]
MCH Reference [0.760 ]..........................[ 0.745 ]
MCH/DRAM Refernce [0.900 ]......................[ 1.00 ] 
ICH I/O [1.500 ]................................[ 1.50 ]
ICH Core [1.100 ]...............................[ 1.10 ]

DRAM Voltage [1.800 ]...........................[ 2.00 ] 
DRAM Termination [0.900 ].......................[ 1.00 ] 
Channel A Ref [0.900 ]..........................[ 1.00 ] 
Channel B Ref [0.900 ]..........................[ 1.00 ] 

******Advanced BIOS Features******

Limit CPUID Max to 3............................[ Disabled ]
No-Execute memory Protect.......................[ Enabled ]
CPU Enhance Halt (CIE)..........................[ Disabled ]
C2/C2E State Support............................[ Disabled ]
C4/C4E State Support............................[ Disabled ]
CPU Thermal Monitor.............................[ Enabled ] 
CPU EIST Function...............................[ Disabled ]
Virtualization Technology.......................[ Disabled ]

*******************************************

[D-an-W]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

I have benched upto 550FSB so far, plenty of info in my "Wont boot above 450FSB" thread (Will post the link when I get home if you like)..

[Octopuss]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

That one I actively check every day :D
You are mad (and probably lick toads :D)

[D-an-W]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

You been watching Eleventh Hour?

I am currently testing 485x8.5 (I have upto 510x8 fully stable) and will see how high I can go with that multiplier before moving onto x9. I can boot and use 500x9 but it isn't Prime stable (yet).

[Octopuss]

Re: Question for other EP45-UD3P owners who hit 500FSB and above

You been watching Eleventh Hour?

nope, just read too many of Lsdme's posts lately :D