Trying to get my Kingston RAM (HyperX PC-8500 KHX8500-D2K2) up to speed. This ran at 1066 in my evga 780i board with manual settings and upping DRAM V to 2.2V.
I've tried various settings with this board and no luck getting it past 533 (it should at least run at 800)
I'm running mild OC on the e8400 (3.6) and just can't get the RAM right. I've clocked the RAM back to the settings I had on my 780i after multiple attempts with different settings. Looking for a little help
CPU-Z (1.51) shows:
DRAM Freq: 533.3 MHz
FSB:DRAM 3:4
CL 5
tRCD 7
tRP 7
tRAS 15
CR 2T
*************************************************
Robust Graphics Booster [Auto]
CPU Clock Ratio[9 X]
Fine CPU Clock Ratio [+0.0]
**********Clock Chip Control*************************
CPU Host Clock Control [Enabled]
CPU Host Frequency (Mhz) [400]
PCI Express Frequency (Mhz) [Auto]
C.I.A 2 [Disabled]
*********Advanced Clock Control**********************
CPU Clock Drive [800mV]
PCI Express Clock Drive [900mV]
CPU Clock Skew [0ps]
MCH Clock Skew [0ps]
**********DRAM Performance Control***********
Performance Enhance [Standard]
Extreme Memory Profile (XMP) [N/A]
(G) MCH Frequency Latch [Auto]
System Memory Multipler [2.66D]
Memory Frequency [800] [1066]
DRAM Timing Selectable [Manual]
CAS Latency Time [5] [Auto]
tRCD [5] [Auto]
tRP [5] [Auto]
tRAS [18] [15]
*******Advanced Timing Control***********
tRRD [3] [Auto]
tWTR [3] [Auto]
tWR [6] [Auto]
tRFC [52] [Auto]
tRTP [3] [Auto]
Command Rate (cmd) [0] [2]
*******Channel A Timing Settings***********
Static tRead Value [8] [Auto]
tRD Phase0 Adjustment [0] [Auto]
tRD Phase1 Adjustment [0] [Auto]
tRD Phase2 Adjustment [1] [Auto]
tRD Phase3 Adjustment [1] [Auto]
Trd2rd (Different Rank) [8] [Auto]
Twr2wr (Different Rank) [8] [Auto]
Twr2rd (Different Rank) [7] [Auto]
Trd2wr (Different Rank) [9] [Auto]
DIMM1 Clock Skew Control [Auto]
DIMM2 Clock Skew Control [Auto]
DDR Write Training [Disabled]
*******Channel A Driving Settings***********
Driving Strength Profile [1066]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
*******Channel B Timing Settings***********
Static tRead Value [8] [Auto]
tRD Phase0 Adjustment [0] [Auto]
tRD Phase1 Adjustment [0] [Auto]
tRD Phase2 Adjustment [1] [Auto]
tRD Phase3 Adjustment [1] [Auto]
Trd2rd (Different Rank) [8] [Auto]
Twr2wr (Different Rank) [8] [Auto]
Twr2rd (Different Rank) [7] [Auto]
Trd2wr (Different Rank) [9] [Auto]
DIMM1 Clock Skew Control [Auto]
DIMM2 Clock Skew Control [Auto]
DDR Write Training [Disabled]
*******Channel B Driving Settings***********
Driving Strength Profile [1066]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
***********Motherboard Voltage Control*******
Load-Line Calibration [Disabled]
CPU Vcore [1.22500V] [1.34375V]
CPU Termination [1.200V] [Auto]
CPU PLL [1.500V] [Auto]
CPU Reference [0.760V] [Auto]
MCH Core [1.100V] [Auto]
MCH Reference [0.760V] [Auto]
MCH/DRAM Refernce [0.900V] [Auto]
ICH I/O [1.500V] [Auto]
ICH Core [1.100V] [Auto]
DRAM Voltage [1.800V] [2.200V]
DRAM Termination [0.900V] [Auto]
Channel A Ref [0.900V] [Auto]
Channel B Ref [0.900V] [Auto]
*****************Advanced BIOS Features*********
CPU Multithreading [N/A]
Limit CPUID Max to 3 [Disabled]
No-Execute memory Protect [Enabled]
CPU Enhance Halt (CIE) [Disabled]
C2/C2E State Support [Disabled]
C4/C4E State Support [Disabled]
CPU Thermal Monitor [Enabled]
CPU EIST Function [Disabled]
Virtualization Technology [Enabled]
I've tried various settings with this board and no luck getting it past 533 (it should at least run at 800)
I'm running mild OC on the e8400 (3.6) and just can't get the RAM right. I've clocked the RAM back to the settings I had on my 780i after multiple attempts with different settings. Looking for a little help
CPU-Z (1.51) shows:
DRAM Freq: 533.3 MHz
FSB:DRAM 3:4
CL 5
tRCD 7
tRP 7
tRAS 15
CR 2T
*************************************************
Robust Graphics Booster [Auto]
CPU Clock Ratio[9 X]
Fine CPU Clock Ratio [+0.0]
**********Clock Chip Control*************************
CPU Host Clock Control [Enabled]
CPU Host Frequency (Mhz) [400]
PCI Express Frequency (Mhz) [Auto]
C.I.A 2 [Disabled]
*********Advanced Clock Control**********************
CPU Clock Drive [800mV]
PCI Express Clock Drive [900mV]
CPU Clock Skew [0ps]
MCH Clock Skew [0ps]
**********DRAM Performance Control***********
Performance Enhance [Standard]
Extreme Memory Profile (XMP) [N/A]
(G) MCH Frequency Latch [Auto]
System Memory Multipler [2.66D]
Memory Frequency [800] [1066]
DRAM Timing Selectable [Manual]
CAS Latency Time [5] [Auto]
tRCD [5] [Auto]
tRP [5] [Auto]
tRAS [18] [15]
*******Advanced Timing Control***********
tRRD [3] [Auto]
tWTR [3] [Auto]
tWR [6] [Auto]
tRFC [52] [Auto]
tRTP [3] [Auto]
Command Rate (cmd) [0] [2]
*******Channel A Timing Settings***********
Static tRead Value [8] [Auto]
tRD Phase0 Adjustment [0] [Auto]
tRD Phase1 Adjustment [0] [Auto]
tRD Phase2 Adjustment [1] [Auto]
tRD Phase3 Adjustment [1] [Auto]
Trd2rd (Different Rank) [8] [Auto]
Twr2wr (Different Rank) [8] [Auto]
Twr2rd (Different Rank) [7] [Auto]
Trd2wr (Different Rank) [9] [Auto]
DIMM1 Clock Skew Control [Auto]
DIMM2 Clock Skew Control [Auto]
DDR Write Training [Disabled]
*******Channel A Driving Settings***********
Driving Strength Profile [1066]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
*******Channel B Timing Settings***********
Static tRead Value [8] [Auto]
tRD Phase0 Adjustment [0] [Auto]
tRD Phase1 Adjustment [0] [Auto]
tRD Phase2 Adjustment [1] [Auto]
tRD Phase3 Adjustment [1] [Auto]
Trd2rd (Different Rank) [8] [Auto]
Twr2wr (Different Rank) [8] [Auto]
Twr2rd (Different Rank) [7] [Auto]
Trd2wr (Different Rank) [9] [Auto]
DIMM1 Clock Skew Control [Auto]
DIMM2 Clock Skew Control [Auto]
DDR Write Training [Disabled]
*******Channel B Driving Settings***********
Driving Strength Profile [1066]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
Data Driving Pull-Up Level [Auto]
Cmd Driving Pull-Up Level [Auto]
Ctrl Driving Pull-Up Level [Auto]
Clk Driving Pull-Up Level [Auto]
***********Motherboard Voltage Control*******
Load-Line Calibration [Disabled]
CPU Vcore [1.22500V] [1.34375V]
CPU Termination [1.200V] [Auto]
CPU PLL [1.500V] [Auto]
CPU Reference [0.760V] [Auto]
MCH Core [1.100V] [Auto]
MCH Reference [0.760V] [Auto]
MCH/DRAM Refernce [0.900V] [Auto]
ICH I/O [1.500V] [Auto]
ICH Core [1.100V] [Auto]
DRAM Voltage [1.800V] [2.200V]
DRAM Termination [0.900V] [Auto]
Channel A Ref [0.900V] [Auto]
Channel B Ref [0.900V] [Auto]
*****************Advanced BIOS Features*********
CPU Multithreading [N/A]
Limit CPUID Max to 3 [Disabled]
No-Execute memory Protect [Enabled]
CPU Enhance Halt (CIE) [Disabled]
C2/C2E State Support [Disabled]
C4/C4E State Support [Disabled]
CPU Thermal Monitor [Enabled]
CPU EIST Function [Disabled]
Virtualization Technology [Enabled]
Comment