I am new here and new to my Gigabyte X58 Extreme MOBO with the Intel i7 Processor. I did find Hicookie's Overclock Profile listed in the BIOS page and dowloaded it. Extracted it to my Floppy disk which showed I now had a .dat file. This doesnt show up this way at the end of Hicookie's Tutorial on Overclocking. I just shows 920A4G 288. Should I rename this by taking out the .dat? Also When I am in the BIOS and hit F12 and actually install this do I make sure to hit Optimize Settings to set this Overclock Profile for sure? Any help would be appreciated and a step by step I wouldnt mind.
Announcement
Collapse
No announcement yet.
Newby wants to try Hicookie's Overclock Profile,Help!
Collapse
X
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
No, the dat file is what you load within the BIOS load profile page. On the Main page hit F12 and navigate to the profile. No you would only load optimized and save/apply/reboot and then set your disk settings, then load the profile and check disk settings again then save/apply and that would be it.
But really, I do suggest against using that profile as it was made for a very old BIOS.
Comment
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
Ya..Almost screwed myself on that one. BIOS did recover though. Not sure everthing is OK though,but it is posting and booting fine for now. Are there any step by step instructions on getting 4MHz out of my Intel i7 though? Thanks for the repleys also.
Comment
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
Anytime, I try to help as much as I can when I can!
Well I'd be on the safe side and go ahead and load optimized defaults again and save/apply/reboot to be sure everything is good to go. I also suggest you update to the latest Beta BIOS if you have not already >>
And Please read this guide for tips and warnings about flashing and loading optimized defaults >>
I can help you for sure with settings, but I need you to post your full specs and a link to your ram. Also let me know what cooler you have, just in case I need to tell you 4Ghz is to much for your cooler, hope not :)
Comment
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
Thanks for the repley. I did just update the BIOS to the F9a for my GA-EX58 Extreme MOBO with great success! Whew! The Q-Flash and a good Ol' Floppy work great! The MOBO is the one I just mentioned above and using the Intel i7 920 Processor w/DO Stepping. Covered with a Cooler Master V8 CPU Cooler and using OCZ Gold XTC OCZ3G1600LV2G Memory.
Timings=@ 533 MHz 7-7-7-16 (CL-RCD-RP-RAS) / 27-59-4-8-4-4 (RC-RFC-RRD-WR-WTR-RTP) @ 457 MHz 6-6-6-14 (CL-RCD-RP-RAS) / 23-51-4-7-4-4 (RC-RFC-RRD-WR-WTR-RTP) @ 380 MHz 5-5-5-12 (CL-RCD-RP-RAS) / 19-42-3-6-3-3 (RC-RFC-RRD-WR-WTR-RTP). I do have a question about my Cooler Master V8. Since it has an outboard Reo-Stat for the V8 Fan control should I disable the CPU Smart Fan Control in the BIOS? Just thought I would ask. My GPU is a XFX Geforce 9800GTX. Let me know if you need more info on my system please. Thanks Also, I am using the Hybrid Silent-Pipe Module included with the MOBO to cool the North Bridge Heat Sink.
Comment
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
Ya, if you are using some other control for your fan then you want to disable fan control in the BIOS
So you want 4Ghz right? I'll assume so for now, not sure how good your cooler is but you should soon find out :)
0X00000050 << Incorrect Memory Timing/Freq or Uncore Multi
0X00000124 << Incorrect QPI/Vtt Voltage (To Much/Not Enough)
0X00000101 << Not enough Vcore Voltage
CPU = Model #
Motherboard = Model, Revision #
BIOS Version =
Ram = Brand, Model#, Part#, And or Link
Code:[B]Advanced CPU Features:[/B] CPU Clock Ratio ................................ [20x] Intel(R) Turbo Boost Tech .................. [Enabled] CPU Cores Enabled ............................ [All] CPU Multi Threading .......................... [Enabled] CPU Enhanced Halt (C1E) ................... [Disabled] C3/C6/C7 State Support .................... [Disabled] CPU Thermal Monitor ......................... [Enabled] CPU EIST Function ............................ [Disabled] Virtualization Technology ................... [Enabled] << Disabled if you do not use Vmware or Virtual PC Programs Bi-Directional PROCHOT ..................... [Enabled] [B]Uncore & QPI Features:[/B] QPI Link Speed .............................. x36 Uncore Frequency .......................... 16-18 (Always 2x memory Multi or 2x +1, 2x +2, ect) Isonchronous Frequency ..................[Enabled] [B]Standard Clock Control:[/B] Base Clock (BCLK) Control ................ [Enabled] BCLK Frequency (MHz) ..................... 200 PCI Express Frequency (MHz) ........... [100] C.I.A.2 [Disabled] [B]Advanced Clock Control:[/B] CPU Clock Drive ..............................[800mV] PCI Express Clock Drive ................... [900mV] CPU Clock Skew ............................. [0ps] IOH Clock Skew ............................. [0ps] [B]Advanced DRAM Features:[/B] Performance Enhance ...................... [Standard] Extreme Memory Profile (X.M.P) ......... [Disabled] System Memory Multiplier (SPD) ........ [AUTO] << Set 8x DRAM Timing Selectable (SPD) .......... [Manual] [B]Channel A + B + C Channel A Timing Settings:[/B] ##Channel A Standard Timing Control## CAS Latency Time ......................8 tRCD .......................................8 tRP .........................................8 tRAS .......................................24 Below values may be left in Auto if you like, generally this is fine. For those users who DO Set advanced timings manually, please see some of my thoughts and findings about these settings and rules here [url=http://www.xtremesystems.org/forums/showpost.php?p=3969957&postcount=3615]XtremeSystems Forums - View Single Post - Gigabyte EX58-UD5/Extreme Discussion Thread[/url] ##Channel A Advanced Timing Control## tRC ........................................ (Should be = tRAS + tRP or above for stability) tRRD ....................................... tWTR ...................................... (Must be Write to Read Delay/Same Rank - (tWL + 4) tWR ........................................ 5-12 (Odd # values likely will fail) tWTP ....................................... (tWTP Must = tWR + tWL + 4) tWL ........................................ (tWL Must be CAS Latency -1) tRFC ....................................... tRTP ....................................... tFAW ...................................... Command Rate (CMD) ................ ##Channel A Misc Timing Control## Round Trip Latency ................... [B]Advanced Voltage Control: CPU[/B] Load Line Calibration ................. [Disabled] CPU Vcore ............................... 1.28-1.42 QPI/VTT Voltage 1.150v ............ 1.34-1.46 CPU PLL 1.800v ....................... 1.8-1.84 [B]MCH/ICH[/B] PCIE 1.500v ........................... 1.5-1.54 QPI PLL 1.100v ....................... 1.14-1.24 IOH Core 1.100v ..................... 1.20-1.26 ICH I/O 1.500v ....................... 1.5-1.6 ICH Core 1.1v ........................1.14-1.2 [B]DRAM[/B] DRAM Voltage 1.500v .............. 1.66 DRAM Termination 0.750v [AUTO] Ch-A Data VRef. 0.750v [AUTO] Ch-B Data VRef. 0.750v [AUTO] Ch-C Data VRef. 0.750v [AUTO] Ch-A Address VRef. 0.750v [AUTO] Ch-B Address VRef. 0.750v [AUTO] Ch-C Address VRef. 0.750v [AUTO]
Last edited by Lsdmeasap; 08-31-2009, 03:12 AM.
Comment
-
Re: Newby wants to try Hicookie's Overclock Profile,Help!
CPU = Model #S-spec: SLBEJ
Motherboard = Model, Revision #Intel X58/ICH10R/rev.1.0
BIOS Version =F9a
Ram = Brand, Model#, Part#, And or Link=http://www.microcenter.com/single_product_results.phtml?product_id=0301254
This might help a little also:[IMG]file:///C:/Users/Kennys/AppData/Local/Temp/moz-screenshot-2.png[/IMG]
[IMG]file:///C:/Users/Kennys/AppData/Local/Temp/moz-screenshot.png[/IMG][IMG]file:///C:/Users/Kennys/AppData/Local/Temp/moz-screenshot-1.png[/IMG]
Comment
Comment