Need Gigabyte MA785GMT-UD2H help with bios?

[andjayik]

I am running xp 64 bit and find my sytem still hangs at times, and may be its my video card? is the onboard video system better then what i have have for video? Maybe i'm missing something in the motherboard settings? I have 2 sata drives and have them at ide settings in the bios? Any help on what the best settings in the bios to make this puppy run faster? I need to know what are good settings in the bios as i find my system kinda slow and should be faster!!!! Am i missing something like haveing 2 sata drives i have them as ide in the bios and any other settings that are important i should change?

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

ArtDrivers will be along shortly to help I am sure, I am not much help with AMD, but I suspect your system hangs due to incorrect settings for your memory most likely.

Can you go ahead and post a link to your memory for him, or give him the model #. And then post your BIOS settings as well, images would be fine if you like.

[andjayik]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

FOR who??

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

To help you out, sorry artdrivers is one of our AMD helpers here at the forums.

Sorry to have confused you

[andjayik]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

thanks, everything is pretty much set at auto. Everything is in my sig. Frequency: 1333MHz Latency: 9-9-9-24 Parity: Unbuffered
Voltage: 1.5V Pins: 240
Density > > > Module: 256Mx64 Chip: 64Mx8

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Which model # Mushkins are those?

[andjayik]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Mushkin EM3-10666 DDR3-1333MHz

model Part Number: 996583

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Artdrivers where are you?

[artdrivers]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Hi andjayik Motherboard Manual ----> http://china.giga-byte.com/FileList/...-ud(s)2h_e.pdf
If you want I can help you with that.
You will want to make some adjustments to your bios for your memory.
I can send you a bios template but first may I ask you for your PC health?
Here is a template please use it. Change the TEMPLATE numbers with yours.
You will need to go into bios. Please always when entering bios on the first bios page press and hold the Ctrl Key and then press the F1. Like at the same time Ctrl+F1. This will allow all bios features to appear.
It is suttle but if viewed closly when Ctrl+F1 is pressed the bios will flicker. This has to be performed everytime you enter bios to view all the features.
The template can be printed up. You should use it and please make any and all changes to the template, (not the bios). Post it here so we can see your current PC Health Status.

PC Health Status
Hardware Thermal Control [Enabled]
Reset Case Open Status [Disabled]
Case Opened No
Vcore 1.364V
DDR3 1.5V 1.536V
+3.3V 3.280V
+12V 12.048V
Current System Temperature 38oC
Current CPU Temperature 36oC
Current CPU FAN Speed 1962 RPM
Current SYSTEM FAN Speed 0 RPM 
Current NB FAN Speed 0 RPM
CPU Warning Temperature [Disabled]
CPU FAN Fail Warning [Disabled]
SYSTEM FAN Fail Warning [Disabled]
NB FAN Fail Warning [Disabled]
CPU Smart FAN Control [Enabled]
CPU Smart FAN Mode [Auto]
System Smart FAN Control [Enabled]

The template can be printed up. You should use them and please make any and all changes to the template, (not the bios). Post it here so we can see your current MB Intelligent Tweaker(M.I.T.).
Before posting this you will want to make the changes in red below and reboot back into bios and remember to press Ctrl+F1 each time to see all of your options.

MB Intelligent Tweaker(M.I.T.)
} Advanced Clock Calibration [Press Enter]
CPU Clock Ratio [Auto] 2800Mhz
CPU NorthBridge Freq. [Auto] 2000Mhz
CPU Host Clock Control [Auto]
x CPU Frequency(MHz) 200
PCIE Clock(MHz) [Auto]
HT Link Width [Auto]
HT Link Frequency [Auto] 2000Mhz
VGA Core Clock control [Disabled]
x VGA Core Clock(MHz) 500
Set Memory Clock [Auto] [COLOR="DarkRed"]manual[/COLOR]
x Memory Clock x6.66 1333Mhz
} DRAM Configuration [Press Enter]
******** System Voltage Optimized ********
System Voltage Control [Manual]
DDR3 Voltage Control [Normal]
NorthBridge Volt Control [Normal]
SouthBridge Volt Control [Normal]
SidePort Mem Volt Controlj [Normal]
CPU NB VID Control [Normal]
CPU Voltage Control [Normal]
Normal CPU Vcore 1.3250V

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Thanks for stopping in!

[artdrivers]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Thanks for stopping in!

Sure we all get busy from time to time.

[Lsdmeasap]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Ya, I know what you mean!

Just letting you know as often as I can how much I personally appreciate your help here with AMD. I always felt terrible in the past not being able to offer much advice on AMD Setups and we didn't have any other active AMD members such as yourself.

So thanks again!

[andjayik]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

Here are my settings, please also advise what to start raising or adjust for overclocking? Would like to hit 3.5mhz


Hardware Thermal Control [Enabled]
Reset Case Open Status [Disabled]
Case Opened yes
Vcore 1.42V
DDR3 1.6V
+3.3V 3.280V
+12V 12.23V
Current System Temperature 32oC
Current CPU Temperature 35oC
Current CPU FAN Speed 1184 RPM
Current SYSTEM FAN Speed 0 RPM
Current NB FAN Speed 0 RPM
CPU Warning Temperature [Disabled]
CPU FAN Fail Warning [Disabled]
SYSTEM FAN Fail Warning [Disabled]
NB FAN Fail Warning [Disabled]
CPU Smart FAN Control [Enabled]
CPU Smart FAN Mode [Auto]
System Smart FAN Control [Enabled]
MB Intelligent Tweaker(M.I.T.)
} Advanced Clock Calibration [Press Enter]
CPU Clock Ratio [Auto] 2900Mhz
CPU NorthBridge Freq. [Auto] 2000Mhz
CPU Host Clock Control [Auto]
x CPU Frequency(MHz) 200
PCIE Clock(MHz) [Auto]
HT Link Width [Auto]
HT Link Frequency [Auto] 2000Mhz
VGA Core Clock control [Disabled]
x VGA Core Clock(MHz) Disabled
Set Memory Clock [Auto] manual
x Memory Clock x6.66 1333Mhz
} DRAM Configuration [Press Enter]
******** System Voltage Optimized ********
System Voltage Control [Manual]
DDR3 Voltage Control [Auto]
NorthBridge Volt Control [Auto]
SouthBridge Volt Control [Auto]
SidePort Mem Volt Controlj [Auto]
CPU NB VID Control [Auto]
CPU Voltage Control [NAuto]
Normal CPU Vcore 1.3250V

[artdrivers]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

OK if you have not yet loaded optimized defaults in bios please do so first.

[andjayik]

Re: Need Gigabyte MA785GMT-UD2H help with bios?

what do u mean optimzed defaults, its either auto enable or disabled in the menu?