Hi.
I've got 2x2GB (Kingstone VR 800MHz CL5) in Dual Channel. I've bought another 2x2GB same brand, same type. And heere we go : after inserting two other sticks, computer kept restarting ith blank screen. I've pulled them out - on my old 2x2GB also same thing. I've tryied everything - matching them with one and other : no luck. One more thing : every stick works fine when put in DDR 0 slot alone. Any ideas?
Motherboard: EP45-DS3LR Model: Rev#1.0: Bios Version: F3a
Cpu: Model E6850
Ram: Kingstone Value RAM DDR2 4x2GB 800MHz
Power Supply Unit: Cheftec APS-550W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [??]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: #### <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [???]
PCI Express Frequency (Mhz) ---------- : [Auto] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Turbo] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [Auto] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [Auto]
tRCD ------------------- ?? ---------- : [Auto]
tRP --------------------- ?? ---------- : [Auto]
tRAS ------------------- ?? ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto]
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- ?.????? ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- ?.???V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ ?.???V ------ : [Auto]
ICH I/O ----------------- ?.???V ------- : [Auto]
ICH Core ---------------- ?.???V ------- : [Auto]
DRAM
DRAM Voltage ------------ ?.???V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Enabled]
C2/C2E State Support ------------------- : [Enabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Enabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
I've got 2x2GB (Kingstone VR 800MHz CL5) in Dual Channel. I've bought another 2x2GB same brand, same type. And heere we go : after inserting two other sticks, computer kept restarting ith blank screen. I've pulled them out - on my old 2x2GB also same thing. I've tryied everything - matching them with one and other : no luck. One more thing : every stick works fine when put in DDR 0 slot alone. Any ideas?
Motherboard: EP45-DS3LR Model: Rev#1.0: Bios Version: F3a
Cpu: Model E6850
Ram: Kingstone Value RAM DDR2 4x2GB 800MHz
Power Supply Unit: Cheftec APS-550W
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster -------------- : [Auto]
CPU Clock Ratio ---------------------- : [??]
Fine CPU Clock Ratio ----------------- : [0.0] <-- ignore if not available
CPU Frequency ---------------------: #### <-- this is set by your bios
Clock Chip Control
Standard Clock Control
CPU Host Clock Control --------------- : [Enabled]
CPU Host Frequency (Mhz) --------------: [???]
PCI Express Frequency (Mhz) ---------- : [Auto] <--- Set to 100, never leave this on Auto
C.I.A.2 ------------------------------ : [Disabled]
Advanced Clock Control ------- [Press Enter]
CPU Clock Drive ---------------------- : [???]
PCI Express Clock Drive -------------- : [???]
CPU Clock Skew (ps) ------------------ : [???]
MCH Clock Skew (ps) ------------------ : [???]
DRAM Performance Control
Performance Enhance ------------------- : [Turbo] <--- set to STANDARD when overclocking
Extreme Memory Profile --- (X.M.P.) --- : [Disabled] <--- Leave this Disabled
(G)MCH Frequency Latch ---------------- : [Auto]
System Memory Multiplier -------------- : [Auto] <-- this is the setting that you are using
Memory Frequency (Mhz) ---------------- : [Auto]
DRAM Timing Selectable ---------------- : [Auto] <-- set to MANUAL for overclocking
Standard Timing Control
CAS Latency Time -------- ?? ---------- : [Auto]
tRCD ------------------- ?? ---------- : [Auto]
tRP --------------------- ?? ---------- : [Auto]
tRAS ------------------- ?? ---------- : [Auto]
Advanced Timing Control
tRRD ------------------- ?? ---------- : [Auto]
tWTR ------------------- ?? ---------- : [Auto]
tWR --------------------- ?? ---------- : [Auto]
tRFC ------------------- ?? ---------- : [Auto]
tRTP ------------------- ?? ---------- : [Auto]
Command Rate (CMD) -------------------- : [Auto]
Channel A
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Channel B
Static tRead Value --------------------- : [Auto]
tRD Phase0 Adjustment ------------------ : [Auto] <-- leave this and below set to AUTO
tRD Phase1 Adjustment ------------------ : [Auto]
tRD Phase2 Adjustment ------------------ : [Auto]
tRD Phase3 Adjustment ------------------ : [Auto]
Trd2rd(Different Rank) ----------------- : [Auto]
Twr2wr(Different Rank) ----------------- : [Auto]
Twr2rd(Different Rank) ----------------- : [Auto]
Trd2wr(Same/Diff Rank) ----------------- : [Auto]
Dimm1 Clock Skew Control --------------- : [Auto] ps
Dimm2 Clock Skew Control --------------- : [Auto] ps
Motherboard Voltage Control
CPU
Voltage Types------------ Normal -------- Current -----
Load-Line Calibration ----------------- : [Disabled]
CPU Vcore --------------- ?.????? ---- : [Auto]
CPU Termination --------- ?.???V* ----- : [Auto]
CPU PLL ----------------- ?.???V* ----- : [Auto]
CPU Reference ----------- ?.???V* ----- : [Auto]
CPU Reference2 ---------- ?.???V* ----- : [Auto]
MCH/ICH
MCH Core ---------------- ?.???V ------- : [Auto]
MCH Reference ----------- ?.???V ------- : [Auto]
MCH/DRAM Ref ------------ ?.???V ------ : [Auto]
ICH I/O ----------------- ?.???V ------- : [Auto]
ICH Core ---------------- ?.???V ------- : [Auto]
DRAM
DRAM Voltage ------------ ?.???V ------- : [Auto]
DRAM Termination -------- ?.???V ------- : [Auto]
Channel A Reference ----- ?.???V ------- : [Auto]
Channel B Reference ----- ?.???V ------- : [Auto]
Advanced Settings
Limit CPUID Max. to 3 ------------------ : [Disabled]
No-Execute Memory Protect -------------- : [Enabled]
CPU Enhanced Halt (C1E) ---------------- : [Enabled]
C2/C2E State Support ------------------- : [Enabled]
x C4/C4E State Support ----------------- : [Disabled]
CPU Thermal Monitor 2 (TM2) ------------ : [Enabled]
CPU EIST Function --------------------- : [Enabled]
Virtualization Technology -------------- : [Disabled]
Integrated Peripherals
Legacy USB Storage Detect ------------- : [Disabled]
Comment